AmplifierA
device used to boost the strength of an
electronic signal.
Amplitude
Modulation (AM)The baseband signal
is caused to vary the amplitude or height of the
carrier wave to create the desired information
content.
AnalogA
form of transmitting information characterized
by continuously variable quantities, as opposed
to digital transmission, which is characterized
by discrete bits of information in numerical
steps. An analog signal is responsive to changes
in light, sound, heat and pressure.
Analog-to-Digital
Conversion (ADC)Process of
converting analog signals to a digital
representation. DAC represents the reverse
translation.
ANIKThe
Canadian domestic satellite system that
transmits Canadian Broadcasting Corporation's
(CSC) network feeds throughout the country. This
system also carries long distance voice and data
services throughout Canada as well as some
transborder service to the U.S. and
Mexico.
AntennaA
device for transmitting and receiving radio
waves. Depending on their use and operating
frequency, antennas can take the form of a
single piece of wire, a di-pole a grid such as a
yagi array, a horn, a helix, a sophisticated
parabolic-shaped dish, or a phase array of
active electronic elements of virtually any flat
or convoluted surface.
ApertureA
cross sectional area of the antenna which is
exposed to the satellite signal.
ApogeeThe
point in an elliptical satellite orbit which is
farthest from the surface of the earth.
Geosynchronous satellites which maintain
circular orbits around the earth are first
launched into highly elliptical orbits with
apogees of 22,237 miles. When the communication
satellite reaches the appropriate apogee, a
rocket motor is fired to place the satellite
into its permanent circular orbit of 22,237
miles.
Apogee
Kick Motor (AKM)Rocket motor fired
to circulate orbit and deploy satellite into
geostationary orbit.
AttenuationThe
loss in power of electromagnetic signals between
transmission and reception points.
Attitude
ControlThe orientation of the
satellite in relationship to the earth and the
sun.
Audio
SubcarrierThe carrier between 5 MHz
and 8 MHz containing audio (or voice)
information inside of a video carrier.
Automatic
Frequency Control (AFC)A circuit
which automatically controls the frequency of a
signal.
Automatic
Gain Control (AGC)A circuit which
automatically controls the gain of an amplifier
so that the output signal level is virtually
constant for varying input signal
levels.
AZ/EL
MountAntenna mount that requires
two separate adjustments to move from one
satellite to another.
AzimuthThe
angle of rotation (horizontal) that a ground
based parabolic antenna must be rotated through
to point to a specific satellite in a
geosynchronous orbit. The azimuth angle for any
particular satellite can be determined for any
point on the surface of the earth giver the
latitude and longitude of that point. It is
defined with respect to due north as a matter of
easy convenience.
back
to topB-MacA
method of transmitting and scrambling television
signals. In such transmissions MAC (Multiplexed
Analog Component) signals are time-multiplexed
with a digital burst containing digitized sound,
video synchronizing, authorization, and
information.
BackhaulA
terrestrial communications channel linking an
earth station to a local switching network or
population center.
BackoffThe
process of reducing the input and output power
levels of a traveling wave tube to obtain more
linear operation.
Band Pass
FilterAn active or passive circuit
which allows signals within the desired
frequency band to pass through but impedes
signals outside this pass band from getting
through.
BandwidthA
measure of spectrum (frequency) use or capacity.
For instance, a voice transmission by telephone
requires a bandwidth of about 3000 cycles per
second (3KHz). A TV channel occupies a bandwidth
of 6 million cycles per second (6 MHz) in
terrestrial Systems. In satellite based systems
a larger bandwidth of 17.5 to 72 MHz is used to
spread or "dither" the television signal in
order to prevent interference.
BasebandThe
basic direct output signal in an intermediate
frequency based obtained directly from a
television camera, satellite television
receiver, or video tape recorder. Baseband
signals can be viewed only on studio monitors.
To display the baseband signal on a conventional
television set a "modulator" is required to
convert the baseband signal to one of the VHF or
UHF television channels which the television set
can be tuned to receive.
BaudThe rate
of data transmission based on the number of
signal elements or symbols transmitted per
second. Today most digital signals are
characterized in bits per second.
BeaconLow-power
carrier transmitted by a satellite which
supplies the controlling engineers on the ground
with a means of monitoring telemetry data,
tracking the satellite, or conducting
propagation experiments. This tracking beacon is
usually a horn or omni antenna.
BeamwidthThe
angle or conical shape of the beam the antenna
projects. Large antennas have narrower
beamwidths and can pinpoint satellites in space
or dense traffic areas on the earth more
precisely. Tighter beamwidths thus deliver
higher levels of power and thus greater
communications performance.
BirdSlang for
a communications satellite located in
geosynchronous orbit.
BitA single
digital unit of information.
Bit Error
RateThe fraction of a sequence of
message bits that are in error. A bit error rate
of 10-6 means that there is an average of one
error per million bits.
Bit
RateThe speed of a digital
transmission, measured in bits per
second.
BlankingAn
ordinary television signal consists of 30
separate still pictures or frames sent every
second. They occur so rapidly, the human eye
blurs them together to form an illusion of
moving pictures. This is the basis for
television and motion picture systems. The
blanking interval is that portion of the
television signal which occurs after one picture
frame is sent and before the next one is
transmitted. During this period of time special
data signals can be sent which will not be
picked up on an ordinary television
receiver.
Block
Down ConverterA device used to
convert the 3.7 to 4.2 KHz signal down to UHF or
lower frequencies (1 GHz and lower).
Broad
BeamA single large circular beam
that covers a large geographic area.
BroadcastThe
sending of one transmission to multiple users in
a defined group (compare to unicast).
Business
TelevisionCorporate communications
tool involving video transmissions of
information via satellite. Common uses of
business television are for meetings, product
introductions and training.
back
to topC-BandThis
is the band between 4 and 8 GHz with the 6 and 4
GHz band being used for satellite
communications. Specifically, the 3.7 to 4.2 GHz
satellite communication band is used as the down
link frequencies in tandem with the 5.925 to
6,425 GHz band that serves as the
uplink.
C/NoCarrier-to-noise
ratio measured either at the Radio Frequency
(RF) or Intermediate Frequency (IF).
C/TCarrier-to-noise-temperature
ratio.
CarrierThe
basic radio, television, or telephony center of
frequency transmit signal. The carrier in an
analog signal. is modulated by manipulating its
amplitude (making it louder or softer) or its
frequency (shifting it up or down) in relation
to the incoming signal. Satellite carriers
operating in the analog mode are usually
frequency modulated.
Carrier
FrequencyThe main frequency on
which a voice, data, or video signal is sent.
Microwave and satellite communications
transmitters operate in the band from 1 to 14
GHz (a GHz is one billion cycles per
second).
Carrier
to Noise Ratio (C/N)The ratio of
the received carrier power and the noise power
in a given bandwidth, expressed in dB. This
figure is directly related to G/T and S/N; and
in a video signal the higher the C/N, the better
the received picture.
Cassegrain
AntennaThe antenna principle that
utilizes a subreflector at the focal point which
reflects energy to or from a feed located at the
apex of the main reflector.
CDMACode
division multiple access. Refers to a
multiple-access scheme where stations use
spread-spectrum modulations and orthogonal codes
to avoid interfering with one another.
ChannelA
frequency band in which a specific broadcast
signal is transmitted. Channel frequencies are
specified in the United States by the Federal
Communications Commission. Television signals
require a 6 MHz frequency band to carry all the
necessary picture detail.
Circular
PolarizationUnlike many domestic
satellites which utilize vertical or horizontal
polarization, the international Intelsat
satellites transmit their signals in a rotating
corkscrew-like pattern as they are down-linked
to earth. On some satellites, both right-hand
rotating and left-hand rotating signals can be
transmitted simultaneously on the same
frequency; thereby doubling the capacity of the
satellite to carry communications
channels.
ClampA video
processing circuit that removes the energy
dispersal signal component from the video
waveform.
Clarke
OrbitThat circular orbit in space
22,237 miles from the surface of the earth at
which geosynchronous satellites are placed. This
orbit was first postulated by the science
fiction writer Arthur C. Clarke in Wireless
World magazine in 1945. Satellites placed in
these orbits, although traveling around the
earth at thousands of miles an hour, appear to
be stationary when viewed from a point on the
earth, since the earth is rotating upon its axis
at the same angular rate that the satellite is
traveling around the earth.
Co-LocationAbility
of multiple satellites to share the same
approximate geostationary orbital assignment
frequently due to the fact that different
frequency bands are used.
CodecCoder/decoder
system for digital transmission.
Color
SubcarrlerA subcarrier that is
added to the main video signal to convey the
color information. In NTSC systems, the color
subcarrier is centered on a frequency of
3.579545 MHz, referenced to the main video
carrier.
Common
CarrierAny organization which
operates communications circuits used by other
people. Common carriers include the telephone
companies as well as the owners of the
communications satellites, RCA, Comsat, Direct
Net Telecommunications, AT&T and others.
Common carriers are required to file fixed
tariffs for specific services.
CompandingA
noise-reduction technique that applies single
compression at the transmitter and complementary
expansion at the receiver.
Composite
BasebandThe unclamped and
unfiltered output of the satellite receiver's
demodulator circuit, containg the video
information as well as all transmitted
subcarriers.
ConusContiguous
United States. In short, all the states in the
U.S. except Hawaii and Alaska.
Cross
ModulationA form of signal
distortion in which modulation from one or more
RF carrier(s) is imposed on another
carrier.
CSUChannel
service unit. A digital interface device that
connects end-user equipment to the local digital
telephone loop. CSU is frequently coupled with
DSU (see below) as CSU/DSU.
back
to topDAMADemand-Assigned
Multiple Access - A highly efficient means of
instantaneously assigning telephony channels in
a transponder according to immediate traffic
demands.
dBiThe dB
power relative to an isotropic source.
DBSDirect
broadcast satellite. Refers to service that uses
satellites to broadcast multiple channels of
television programming directly to home mounted
small-dish antennas.
dBWThe ratio
of the power to one Watt expressed in
decibels.
Decibel
(dB)The standard unit used to
express the ratio of two power levels. It is
used in communications to express either a gain
or loss in power between the input and output
devices.
DeclinationThe
offset angle of an antenna from the axis of its
polar mount as measured in the meridian plane
between the equatorial plane and the antenna
main beam.
DecoderA
television set-top device which enables the home
subscriber to convert an electronically
scrambled television picture into a viewable
signal. This should not be confused with a
digital coder/decoder known as a CODEC which is
used in conjunction with digital
transmissions.
DeemphasisReinstatement
of a uniform baseband frequency response
following demodulation.
DelayThe
time it takes for a signal to go from the
sending station through the satellite to the
receiving station. This transmission delay for a
single hop satellite connection is very close on
one-quarter of a second.
DemodulatorA
satellite receiver circuit which extracts or
"demodulates" the "wanted "signals from the
received carrier.
DeviationThe
modulation level of an FM signal determined by
the amount of frequency shift from the frequency
of the main carrier.
DigitalConversion
of information into bits of data for
transmission through wire, fiber optic cable,
satellite, or over air techniques. Method allows
simultaneous transmission of voice, data or
video.
Digital
Speech InterpolationDSI - A means
of transmitting telephony. Two and One half to
three times more efficiently based on the
principle that people are talking only about 40%
of the time.
DownlinkThe
satellite to earth half of a 2 way
telecommunications satellite link. Often used to
describe the recieve dish end of the
link.
DSUData
service unit. A device used in digital
transmission that adapts the physical interface
on a DTE device to a transmission facility such
as T1 or E1. The DSU is also responsible for
such functions as signal timing. DSU is
freqnetly coupled with a CSU (see above) as
CSU/DSU.
DTVDigital
Television.
Dual
SpinSpacecraft design whereby the
main body of the satellite is spun to provide
altitude stabilization, and the antenna assembly
is despun by means of a motor and bearing system
in order to continually direct the antenna
earthward. This dual-spin configuration thus
serves to create a spin stabilized
satellite.
Duplex
TransmissionCapability for
simultaneous data transmission between a sending
station and a receiving station.
DVBDigital
Video Broadcasting - The European-backed project
to harmonise adoption of digital
video.
back
to topE1Wide-area
digital transmission facility used predominantly
in Europe that carries data at a rate of 2.048
Mbit/s.
E3Wide-area
digital transmission facility used predominantly
in Europe that carries data at a rate of 34.368
Mbit/s.
Earth
StationThe term used to describe
the combination or antenna, low-noise amplifier
(LNA), down-converter, and receiver electronics.
used to receive a signal transmitted by a
satellite. Earth Station antennas vary in size
from the.2 foot to 12 foot (65 centimeters to
3.7 meters) diameter size used for TV reception
to as large as 100 feet (30 meters) in diameter
sometimes used for international communications.
The typical antenna used for INTELSAT
communication is today 13 to 18 meters or 40 to
60 feet.
Echo
CancellerAn electronic circuit
which attenuates or eliminates the echo effect
on satellite telephony links. Echo cancellers
are largely replacing obsolete echo
suppressors.
Echo
EffectA time-delayed electronic
reflection of a speaker's voice. This is largely
eliminated by modern digital echo
cancellers.
Edge of
CoverageLimit of a satellite's
defined service area. In many cases, the EOC is
defined as being 3 dB down from the signal level
at beam center. However, reception may still be
possible beyond the -3dB point.
EIRPEffective
Isotropic Radiated Power - This term describes
the strength of the signal leaving the satellite
antenna or the transmitting earth station
antenna, and is used in determining the C/N and
S/N. The transmit power value in units of dBW is
expressed by the product of the transponder
output power and the gain of the satellite
transmit antenna.
ElevationThe
upward tilt to a satellite antenna measured in
degrees required to aim the antenna at the
communications satellite. When. aimed at the
horizon, the elevation angle is zero. If it were
tilted to a point directly overhead, the
satellite antenna would have an elevation of 90
degrees.
EncoderA
device used to electronically alter a signal so
that it can only be viewed on a receiver
equipped with a special decoder.
EOLEnd of Life
of a satellite.
Equatorial
OrbitAn orbit with a plane parallel
to the earth's equator.
ESCEngineering
Service Circuit - The 300-3,400 Hertz voice plus
teletype (S+DX) channel used for earth
station-to-earth station and earth
station-to-operations center communications for
the purpose of system maintenance, coordination
and general system information dissemination. In
analog (FDM/FM) systems there are two S+DX
channels available for this purpose in the
4,000-12,000 Hertz portion of the baseband. In
digital systems there are one or two channels
available which are usually convened to a 32 or
64 Kbps digital signal and combined with the
earth station traffic digital bit stream. Modern
ESC equipment interfaces with any mix of analog
and digital satellite carriers, as well as
backhaul terrestrial links to the local
switching center.
back
to topF/DRatio of
antenna focal length to antenna diameter. A
higher ratio means a shallower dish.
FDMAFrequency
division multiple access. Refers to the use of
multiple carriers within the same transponder
where each uplink has been assigned frequency
slot and bandwidth. This is usually employed in
conjunction with Frequency Modulation.
FeedThis term
has at least two key meanings within the field
of satellite communications. It is used to
describe the transmission of video programming
from a distribution center. It is also used to
describe the feed system of an antenna. The feed
system may consist of a subreflector plus a
feedhorn or a feedhorn only.
Focal
LengthDistance from the center feed
to the center of the dish.
Focal
PointThe area toward which the
primary reflector directs and concentrates the
signal received.
FootprintA
map of the signal strength showing the EIRP
contours of equal signal strengths as they cover
the earth's surface. Different satellite
transponders on the same satellite will often
have different footprints of the signal
strength. The accuracy of EIRP footprints or
contour data can improve with the operational
age of the satellite. The actual EIRP levels of
the satellite, however, tends to decrease slowly
as the spacecraft ages.
Forward
Error Correction (FEC)Adds unique
codes to the digital signal at the source so
errors can be detected and corrected at the
receiver.
FrequencyThe
number of times that an alternating current goes
through its complete cycle in one second of
time. One cycle per second is also referred to
as one hertz; 1000 cycles per second, one
kilohertz; 1,000,000 cycles per second, one
megahertz: and 1,000,000,000 cycles per second,
one gigahertz.
Frequency
CoordinationA process to eliminate
frequency interference between different
satellite systems or between terrestrial
microwave systems and satellites. In the U.S.
this activity relies upon a computerized service
utilizing an extensive database to analyze
potential microwave interference problems that
arise between organizations using the same
microwave band. As the same C-band frequency
spectrum is used by telephone networks and CATV
companies when they are contemplating the
installation of an earth station, they will
often obtain a frequency coordination study to
determine if any problems will exist.
back
to topG/TA figure of
merit of an antenna and low noise amplifier
combination expressed in dB. "G" is the net gain
of the system and "T" is the noise temperature
of the system. The higher the number, the better
the system.
GainA measure
of amplification expressed in dB.
GeostationaryRefers
to a geosynchronous satellite angle with zero
inclination. so the satellite appears to hover
over one spot on the earth's equator.
GeosynchronousThe
Clarke circular orbit above the equator. For a
planet the size and mass of the earth, this
point is 22,237 miles above the
surface.
Gigahertz
(GHz)One billion cycles per second.
Signals operating above 3 Gigahertz are known as
microwaves. above 30 GHz they are know as
millimeter waves. As one moves above the
millimeter waves signals begin to take on the
characteristics of Iightwaves.
Global
BeamAn antenna down-link pattern
used by the Intelsat satellites, which
effectively covers one-third of the globe.
Global beams are aimed at the center of the
Atlantic, Pacific and Indian Oceans by the
respective Intelsat satellites, enabling all
nations on each side of the ocean to receive the
signal. Because they transmit to such a wide
area, global beam transponders have
significantly lower EIRP outputs at the surface
of the Earth as compared to a US domestic
satellite system which covers just the
continental United States. Therefore, earth
stations receiving global beam signals need
antennas much larger in size (typically 10
meters and above (i.e.30 feet and up). Gregorian
Dual-reflector antenna system employing a
paraboloidal main reflector and a concave
ellipsoidal subreflector.
Guard
ChannelTelevision channels are
separated in the frequency spectrum by spacing
them several megahertz apart. This unused space
serves to prevent the adjacent television
channels from interfering with each
other.
back
to topHalf
TransponderA method of transmitting
two TV signals through a single transponder
through the reduction of each TV signal's
deviation and power level. Half-transponder TV
carriers each operate typically 4 dB to 7 dB
below single-carrier saturation power.
HeadendElectronic
control center - generally located at the
antenna site of a CATV system - usually
including antennas, preamplifiers, frequency
converters, demodulators and other related
equipment which amplify, filter and convert
incoming broadcast TV signals to cable system
channels.
Hertz
(Hz)The name given to the basic
measure of radio frequency characteristics. An
electromagnetic wave completes a full
oscillation from its positive to its negative
pole and back again in what is known as a cycle.
A single Hertz is thus equal to one cycle per
second.
HubThe master
station through which all communications to,
from and between micro terminals must flow. in
the future satellites with on-board processing
will allow hubs to be eliminated as MESH
networks are able to connect all points in a
network together.
back
to topIBSINTELSAT
Business Services.
InclinationThe
angle between the orbital plane of a satellite
and the equatorial plane of the earth.
INMARSATThe
International Maritime Satellite Organization
operates a network of satellites for
international transmissions for all types of
international mobile services including
maritime, aeronautical, and land
mobile.
INTELSATThe
International Telecommunications Satellite
Organization operates a network of satellites
for international transmissions.
InterferenceEnergy
which tends to interfere with the reception of
the desired signals, such as fading from airline
flights, RF interference from adjacent channels,
or ghosting from reflecting objects such as
mountains and buildings.
IRDAn
integrated receiver and decoder for reception of
a transmission of voice, video and
data.
ISDN
- Integrated Services Digital
Network.A CCITT standard for
integrated transmission of voice, video and
data. Bandwidths include: Basic Rate Interface -
BR (144 Kbps - 2 B & 1 D channel) and
Primary Rate - PRI (1.544 and 2.048
Mbps).
Isotropic
AntennaA hypothetical
omnidirectional point-source antenna that serves
as an engineering reference for the measurement
of antenna gain.
ITUInternational
Telecommunication Union.
back
to topJammerAn
active electronic counter-measures (ECM) device
designed to deny intelligence to unfriendly
detectors or to disrupt
communications.
JPEGISO Joint
Picture Expert Group standard for the
compression of still pictures.
back
to topKa-BandThe
frequency range from 18 to 31 GHz.
KbpsKilobits
per second. Refers to transmission speed of
1,000 bits per second.
Kelvin
(K)The temperature measurement
scale used in the scientific community. Zero K
represents absolute zero, and corresponds to
minus 459 degrees Fahrenheit or minus 273
Celsius. Thermal noise characteristics of LNA
are measured in Kelvins.
Kilohertz
(kHz)Refers to a unit of frequency
equal to 1,000 Hertz.
KlystronA
microwave tube which uses the interaction
between an electron beam and the RF energy on
microwave cavities to provide signal
amplification. The klystron operates on
principles of velocity modulation very similar
to those in a TWT except that klystron
interaction takes place at discrete locations
along the electron beam. Common types of
klystrons are the reflex klystron (an oscillator
having only one cavity), two-cavity klystron
amplifiers and oscillators, and multi-cavity
klystron amplifiers.
Ku-BandThe
frequency range from 10.9 to 17 GHz.
back
to topL-BandThe
frequency range from 0.5 to 1.5 GHz. Also used
to refer to the 950 to 1450MHz used for mobile
communications.
Leased
LineA dedicated circuit typically
supplied by the telephone company.
Low
Noise Amplifier (LNA)This is the
preamplifier between the antenna and the earth
station receiver. For maximum effectiveness, it
must be located as near the antenna as possible,
and is usually attached directly to the antenna
receive port. The LNA is especially designed to
contribute the least amount of thermal noise to
the received signal.
Low
Noise Block Downconverter (LNB)A
combination Low Noise Amplifier and
downconverter built into one device attached to
the feed.
back
to topMAC (A, B,
C, D2)Multiplexed analog component
color video transmission system. Subtypes refer
to the various methods used to transmit audio
and data signals.
MarginThe
amount of signal in dB by which the satellite
system exceeds the minimum levels required for
operation.
Master
Antenna Television (MATV)An antenna
system that serves a concentration of television
sets such as in apartment buildings, hotels or
motels.
Megahertz
(MHz)Refers to a frequency equal to
one million Hertz, or cycles per
second.
MicrowaveLine-of
sight, point-to-point transmission of signals at
high frequency. Many CATV systems receive some
television signals from a distant antenna
location with the antenna and the system
connected by microwave relay. Microwaves are
also used for data, voice, and indeed all types
of information transmission. The growth of fiber
optic networks have tended to curtail the growth
and use of microwave relays.
Microwave
InterferenceInterference which
occurs when an earth station aimed at a distant
satellite picks up a second, often stronger
signal, from a local telephone terrestrial
microwave relay transmitter. Microwave
interference can also be produced by nearby
radar transmitters as well as the sun itself.
Relocating the antenna by only several feet will
often completely eliminate the microwave
interference.
ModulationThe
process of manipulating the frequency or
amplitude of a carrier in relation to an
incoming video, voice or data signal.
ModulatorA
device which modulates a carrier. Modulators are
found as components in broadcasting transmitters
and in satellite transponders. Modulators are
also used by CATV companies to place a baseband
video television signal onto a desired VHF or
UHF channel. Home video tape recorders also have
built-in modulators which enable the recorded
video information to be played back using a
television receiver tuned to VHF channel 3 or
4.
MPEGThe
Moving Pictures Experts Group, the television
industry's informal standards group.
MPEG-2The
agreed standard covering the compression of data
(coding and encoding) for digital
television.
MPEG-2
MP@HLMain Provile at High Level -
The agreed much higher bit-rate system adopted
to provide high definition television in wide
screen format.
MulticastMulticast
is a subset of broadcast that extends the
broadcast concept of one to many by allowing
"the sending of one transmission to many users
in a defined group, but not necessarily to all
users in that group."
MultiplexingTechniques
that allow a number of simultaneous
transmissions over a single circuit.
back
to topNoiseAny
unwanted and unmodulated energy that is always
present to some extent within any
signal.
Noise
Figure (NF)A term which is a figure
of merit of a device, such as an LNA or
receiver, expressed in dB, which compares the
device with a perfect device.
back
to topNTSC
- National Television Standards
CommitteeA video standard
established by the United States (RCA/NBC} and
adopted by numerous other countries. This is a
525-line video with 3.58-MHz chroma subcarrier
and 60 cycles per second.
Orbital
PeriodThe time that it takes a
satellite to complete one circumnavigation of
its orbit.
back
to topPacket
SwitchingData transmission method
that divides messages into standard-sized
packets for greater efficiency of routing and
transport through a network.
PAL
- Phase Alternation SystemThe
German developed TV standard based upon 50
cycles per second and 625 lines.
Parabolic
AntennaThe most frequently found
satellite TV antenna, it takes its name from the
shape of the dish described mathematically as a
parabola. The function of the parabolic shape is
to focus the weak microwave signal hitting the
surface of the dish into a single focal point in
front of the dish. It is at this point that the
feedhorn is usually located.
Phase-Locked
Loop (PLL)A type of electronic
circuit used to demodulate satellite
signals.
Polar
MountAntenna mechanism permitting
steering in both elevation and azimuth through
rotation about a single axis. While an
astronomer's polar mount has its axis parallel
to that of the earth, satellite earth stations
utilize a modified polar mount geometry that
incorporates a declination offset.
Polar
OrbitAn orbit with its plane
aligned in parallel with the polar axis of the
earth.
PolarizationA
technique used by the satellite designer to
increase the capacity of the satellite
transmission channels by reusing the satellite
transponder frequencies. In linear cross
polarization schemes, half of the transponders
beam their signals to earth in a vertically
polarized mode; the other half horizontally
polarize their down links. Although the two sets
of frequencies overlap, they are 90 degree out
of phase, and will not interfere with each
other. To successfully receive and decode these
signals on earth, the earth station must be
outfitted with a properly polarized feedhorn to
select the vertically or horizontally polarized
signals as desired. In some installations, the
feedhorn has the capability of receiving the
vertical and horizontal transponder signals
simultaneously, and routing them into separate
LNAs for delivery to two or more satellite
television receivers. Unlike most domestic
satellites, the Intelsat series use a technique
known as left-hand and right-hand circular
polarization.
Polarization
RotatorA device that can be
manually or automatically adjusted to select one
of two orthogonal polarizations.
PTT
- Post Telephone and Telegraph
AdministrationRefers to operating
agencies directly or indirectly controlled by
governments in charge of telecommunications
services in most countries of the
world.
Pulse
Code ModulationA time division
modulation technique in which analog signals are
sampled and quantized at periodic intervals into
digital signals. The values observed are
typically represented by a coded arrangement of
8 bits of which one may be for parity.
back
to topQPSK
- Quadrature Phase Shift
KeyingSystem of modulating a
satellite signal.
back
to topRain
OutageLoss of signal at Ku or Ka
Band frequencies due to absorption and increased
sky-noise temperature caused by heavy
rainfall.
Receiver
(Rx)An electronic device which
enables a particular satellite signal to be
separated from all others being received by an
earth station, and converts the signal format
into a format for video, voice or
data.
Receiver
SensitivityExpressed in dBm this
tells how much power the detector must receive
to achieve a specific baseband performance, such
as a specified bit error rate or signal to noise
ratio.
RouterNetwork
layer device that determines the optimal path
along which network traffic should be forwarded.
Routers forward packets from one network to
another based on network layer
information.
back
to topSatelliteA
sophisticated electronic communications relay
station orbiting 22,237 miles above the equator
moving in a fixed orbit at the same speed and
direction of the earth (about 7,000 mph east to
west).
Scalar
FeedA type of horn antenna feed
which uses a series of concentric rings to
capture signals that have been reflected toward
the focal point of a parabolic
antenna.
ScramblerA
device used to electronically alter a signal so
that it can only be viewed or heard on a
receiver equipped with a special
decoder.
SecamA color
television. system developed by the French and
used in the USSR. Secam operates with 625 lines
per picture frame and 50 cycles per second, but
is incompatible in operation with the European
PAL system or the U.S. NTSC system.
SFD
- Stauration Flux DensityThe power
required to achieve saturation of a single
repeater channel on the satellite.
SidelobeOff-axis
response of an antenna.
Signal
to Noise Ratio (S/N)The ratio of
the signal power and noise power. A video S/N of
54 to 56 dB is considered to be an excellent
S/N, that is, of broadcast quality. A video S/N
of 48 to 52 dB is considered to be a good S/N at
the headend for Cable TV.
Simplex
TransmissionCapability for
transmission in only one direction between
sending station and receiving station.
Single-Channel-Per-Carrier
(SCPC)A method used to transmit a
large number of signals over a single satellite
transponder.
SkewAn
adjustment that compensates for slight variance
in angle between identical senses of polarity
generated by two or more satellites.
Slant
RangeThe length of the path between
a communications satellite and an associated
earth station.
SlotThat
longitudinal position in the geosynchronous
orbit into which a communications satellite is
"parked". Above the United States,
communications satellites are typically
positioned in slots which are based at two to
three degree intervals.
SNGSatellite
news gathering usually with a transportable
uplink truck.
SnowA form of
noise picked up by a television receiver caused
by a weak signal. Snow is characterized by
alternate dark and light dots appearing randomly
on the picture tube. To eliminate snow, a more
sensitive receive antenna must be used, or
better amplification must be provided in the
receiver (or both).
Solar
OutageSolar outages occur when an
antenna is looking at a satellite, and the sun
passes behind or near the satellite and within
the field of view of the antenna. This field of
view is usually wider than the beamwidth. Solar
outages can be exactly predicted as to the
timing for each site.
SpectrumThe
range of electromagnetic radio frequencies used
in transmission of voice, data and
television.
SpilloverSatellite
signal that falls on locations outside the beam
pattern's defined edge of coverage.
Spin
StabilizationA form of satellite
stabilization and attitude control which is
achieved through spinning the exterior of the
spacecraft about its axis at a fixed
rate.
SplitterA
passive device (one with no active electronic
components) which distributes a television
signal carried on a cable in two or more paths
and sends it to a number of receivers
simultaneously.
Spot
BeamA focused antenna pattern sent
to a limited geographical area. Spot beams are
used by domestic satellites to deliver certain
transponder signals to geographically well
defined areas such as Hawaii, Alaska and Puerto
Rico.
Spread
SpectrumThe transmission of a
signal using a much wider bandwidth and power
than would normally be required. Spread spectrum
also involves the use of narrower signals that
are frequency hopped through various parts of
the transponder. Both techniques produce low
levels of interference Between the users. They
also provide security in that the signals appear
as though they were random noise to unauthorized
earth stations. Both military and civil
satellite applications have developed for spread
spectrum transmissions.
SSPASolid
state power amplifier. A VSLI solid state device
that is gradually replacing Traveling Wave Tubes
in satellite communications systems because they
are lighter weight and are more
reliable.
StationkeepingMinor
orbital adjustments that are conducted to
maintain the satellite's orbital assignment
within the allocated "box" within the
geostationary arc.
SubcarrierA
second signal "piggybacked" onto a main signal
to carry additional information. In satellite
television transmission, the video picture is
transmitted over the main carrier. The
corresponding audio is sent via an FM
subcarrier. Some satellite transponders carry as
many as four special audio or data subcarriers
whose signals may or may not be related to the
main programming.
Synchronization
(Sync)The process of orienting the
transmitter and receiver circuits in the proper
manner in order that they can be synchronized .
Home television sets are synchronized by an
incoming sync signal with the television cameras
in the studios 60 times per second. The
horizontal and vertical hold controls on the
television set are used to set the receiver
circuits to the approximate sync frequencies of
incoming television picture and the sync pulses
in the signal then fine tune the circuits to the
exact frequency and phase.
back
to topT1The
transmission bit rate of 1.544 millions bits per
second. This is also equivalent to the ISDN
Primary Rate Interface for the U.S. The European
T1 or E1 transmission rate is 2.048 million bits
per second.
T3 Channel
(DS-3)In North America, a digital
channel which communicates at 45.304
Mbps.
TDMATime
division multiple access. Refers to a form of
multiple access where a single carrier is the
shared by many users. Signals from earth
stations reaching the satellite consecutively
are processed in time segments without
overlapping.
TI
- Terrestrial
InterferenceInterference to
satellite reception caused by ground based
microwave transmitting stations.
TransmitterAn
electronic device consisting of oscillator,
modulator and other circuits which produce a
radio or television electromagnetic wave signal
for radiation into the atmosphere by an
antenna.
TransponderA
combination receiver, frequency converter, and
transmitter package, physically part of a
communications satellite. Transponders have a
typical output of five to ten watts, operate
over a frequency band with a 36 to 72 megahertz
bandwidth in the L, C, Ku, and sometimes Ka
Bands or in effect typically in the microwave
spectrum, except for mobile satellite
communications. Communications satellites
typically have between 12 and 24 onboard
transponders although the INTELSAT VI at the
extreme end has 50.
TVROTelevision
Receive Only terminals that use antenna
reflectors and associated electronic equipment
to receive and process television and audio
communications via satellite. Typically small
home systems.
TweekingThe
process of adjusting an electronic receiver
circuit to optimize its performance.
TWT
(Traveling-wave tube)A microwave
tube of special design using a broadband circuit
in which a beam of electrons interacts
continuously with a guided electromagnetic field
to amplify microwave frequencies.
TWTA
(Traveling-wave-tube amplifier)A
combination of a power supply, a modulator (for
pulsed systems), and a traveling-wave tube,
often packaged in a common enclosure.
back
to topUnicastA
unicast application transmits a copy of every
packet to every receiver.
UplinkThe
earth station used to transmit signals to a
satellite.
back
to topV.35ITU-T
standard describing a synchronous, physical
layer protocol used for communications between a
network access device and a packet network. V.35
is most commonly used in the United States and
in Europe, and is recommended for speeds up to
48 Kbit/s.
VSATVery
small aperture terminal. Refers to small earth
stations, usually in the 1.2 to 2.4 meter range.
Small aperture terminals under 0.5 meters are
sometimes referred to Ultra Small Aperture
Terminals (USAT's).
VSWRVoltage
Standing Wave Ratio. A measurement of mismatch
in a cable, waveguide, or antenna
system.
back
to topWaveguideA
metallic microwave conductor, typically
rectangular in shape, used to carry microwave
signals into and out of microwave
antennas.
back
to topX.25A set of
packet switching standards published by the
CCITT.
back
to
top